Are You Adding a Tourpak to your 2015 RG? - Road Glide Forums
 10Likes
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 40 (permalink) Old 07-05-2015, 10:01 PM Thread Starter
Hangaround
 
nking262's Avatar
 
Join Date: Apr 2012
Location: Dallas, NC
Posts: 143
Garage
Parts Needed for Adding Tourpak/speakers/lights to your 2015 RG?

I will have my list to post all the parts needed to do a king tourpak with wrap around light bar and speaker pods in the next day or two but I found this on the web and it may help some of you with wiring problems. This appears to be what people are hunting for to add rear lights. Hope it helps. Let us know.

http://www.baddad.com/products/part/81009

Thanks,
Nick

Last edited by nking262; 07-13-2015 at 07:49 PM. Reason: Updating post
nking262 is offline  
Sponsored Links
Advertisement
 
post #2 of 40 (permalink) Old 07-06-2015, 08:59 PM
Newbie
 
Join Date: May 2015
Location: Dayton, Ohio
Posts: 9
Tour pack lights

Ref the wire harness from bad dad. Is this a "Y" type of harness? I have my tour pack and lights mounted but trying to figure out a wire harness to attach to the oem harness. I have a 2015 RG and there is only one plug that goes to the oem rear lights. I was thinking of going off this plug that is under the seat. Either by putting in a Y harness so that I could tie into the oem rear lights or just tie in to each wire. Can I do this without a equalizer for LEDs on the tour pack lights since this is the lead that goes to the oem lights?
steve79usa likes this.
rottman is offline  
post #3 of 40 (permalink) Old 07-07-2015, 10:26 PM Thread Starter
Hangaround
 
nking262's Avatar
 
Join Date: Apr 2012
Location: Dallas, NC
Posts: 143
Garage
The 2015 does NOT require the load equalizer. Just remember, the rear tail lights that come on it are not LED so you will need to change them if you plan to use the Custom Dynamics module. I will take a good look at mine tomorrow and post some pictures so you all can see how it all wires up. Not sure about the harness from Baddad, you will need to contact them to verify.
Nick
Sparkyfl likes this.

Last edited by nking262; 07-07-2015 at 10:30 PM.
nking262 is offline  
 
post #4 of 40 (permalink) Old 07-13-2015, 05:21 PM Thread Starter
Hangaround
 
nking262's Avatar
 
Join Date: Apr 2012
Location: Dallas, NC
Posts: 143
Garage
Pictures and part numbers to add tourpak to 2015 RG

Okay, I am hoping all the pictures and forms come out so you can see what is what and have the information to add a tourpak to your 2015 RG. I added the wrap around led tail light kit and speaker pods so it will look like it came from the factory that way(except for a few touches). I do want to state something very obvious, the HARLEY DEALER WILL NOT DO AS NICE A JOB AS YOU CAN DO YOURSELF! I had to go back and take plugs off the wiring and relocate my wiring from the outside of the tourpak and put everything inside like it should have been. I am attaching pictures of their install, my changes, and the parts list from the dealer that should have everything they used(they did not put the actual wire length, size or color for the interconnect cable they made to hook up the tourpak lights). If you have any questions about what was done, just ask and I will answer as best I can, I have been working on these a long time myself.
Hope this helps.
Attached Images
File Type: jpg SAM_0999.jpg (98.0 KB, 400 views)
File Type: jpg SAM_1039.jpg (92.2 KB, 360 views)
AFD68 likes this.
nking262 is offline  
post #5 of 40 (permalink) Old 07-13-2015, 05:49 PM
Life Member
 
tdkkart's Avatar
 
Join Date: Jun 2011
Location: East Central Iowa
Posts: 3,042
Garage
What was your final cost?? When I was looking at buying I had several numbers, anywhere from $16-2500 depending on how much of it you wanted.

2015 RGU CVO........under continuous change......
tdkkart is offline  
post #6 of 40 (permalink) Old 07-13-2015, 05:51 PM Thread Starter
Hangaround
 
nking262's Avatar
 
Join Date: Apr 2012
Location: Dallas, NC
Posts: 143
Garage
Pictures and parts

This should be copies of the parts from HD.
Attached Images
File Type: jpg SAM_1054.jpg (88.8 KB, 373 views)
File Type: jpg SAM_1056.jpg (87.9 KB, 270 views)
nking262 is offline  
post #7 of 40 (permalink) Old 07-13-2015, 06:03 PM Thread Starter
Hangaround
 
nking262's Avatar
 
Join Date: Apr 2012
Location: Dallas, NC
Posts: 143
Garage
Wiring

I have the Custom Dynamics module on my brake lights and I know it would be confusing if I tried to show it in the setup, so I am going to show it without it hooked up. Also showing it without the saddlebag lights hooked up. The wiring and plugs in front of the battery is the module for the saddlebag lights so they will not be used here. This way you can see how the tourpak hooks up to the bike itself.
The 2 plugs that you will use are on harness HD#69200129-REV 0 and plugs into HD#69200623-REV D. The harness that you see in the next post will plug in between the 2 plugs on one end and the other end will plug into the harness that is in the tourpak itself.
Attached Images
File Type: jpg SAM_1012.jpg (85.4 KB, 246 views)
File Type: jpg SAM_1019.jpg (92.8 KB, 243 views)
nking262 is offline  
post #8 of 40 (permalink) Old 07-13-2015, 06:17 PM Thread Starter
Hangaround
 
nking262's Avatar
 
Join Date: Apr 2012
Location: Dallas, NC
Posts: 143
Garage
Wiring to tourpak

Now for pictures of the harness that you will need to make or find if you plan to order one. This harness has the HD 6 pin connectors on it that are on the list.
HD# 72414-07BK is the 6-way socket housing and HD# 72188-07BK is the 6-way pin housing. The list states 2 each but there are 2 sockets and 1 pin if I am correct(has the white cover inside and you cannot see the pins).
To make one you will basically have to make a harness with one of each plugs on it and on the pin end, add a socket housing and make a jumper for each of the wires so they are wired exactly as the socket on the other end is. I do not have the wiring colors yet so I cannot help on that now. You will also have to identify pin locations and wire colors from the manual so you have them in the correct place. If no-one can locate an aftermarket harness or get a diagram for it, let me know and I will sit down and draw up a diagram for this harness.
Attached Images
File Type: jpg SAM_1014.jpg (94.6 KB, 213 views)
File Type: jpg SAM_1017.jpg (88.5 KB, 192 views)
nking262 is offline  
post #9 of 40 (permalink) Old 07-13-2015, 06:54 PM Thread Starter
Hangaround
 
nking262's Avatar
 
Join Date: Apr 2012
Location: Dallas, NC
Posts: 143
Garage
Wiring in tourpak

Okay, hope this is helping. Now for the tourpak itself, if you are adding any lights to it. I went ahead and ordered the harness for the entire tourpak that way I had all the wiring for any of the stock lights I wanted to add. The part number is HD#69200131. You will need to put a grommet in the bottom of the tourpak and put your wiring thru it from the inside. If you see mine, on the brake side, the dealer just cut the grommet because they were too lazy to take the plug off the end of the harness and feed the wires down thru the grommet. But if I were you, I would write down the locations of the wires, or take a picture, and take the plug housing off and do it the right way. Pictures show the harness inside the tourpak and where it goes thru to the outside. Get some clear packing tape and tape the harness down so it does not rub around in there. Plug in whichever lights you add. If you are adding the wrap around light kit, HD#67800368- smoke lens, or the red one, you wil;l have to get all the hardware listed on the second page of parts because they do not come with it so you will not have anything to mount it to the tourpak. Thanks Harley... Keep in mind as you look at these pictures, the harness for the lights is underneath the metal pan in the bottom of the tourpak.
Attached Images
File Type: jpg SAM_1025.jpg (89.7 KB, 243 views)
File Type: jpg SAM_1036.jpg (94.1 KB, 297 views)
nking262 is offline  
post #10 of 40 (permalink) Old 07-13-2015, 07:23 PM Thread Starter
Hangaround
 
nking262's Avatar
 
Join Date: Apr 2012
Location: Dallas, NC
Posts: 143
Garage
Wiring for rear speakers and speaker pods

Now that we have some lighting details out of the way, here is some info on getting your rear speakers to work and what you will need for wiring. The speaker pod kit comes with the bass ports so these directions are for running your speaker wires inside the tourpak, thru the ports and not outside the tourpak, exposed to the weather and passenger. On the list of parts you will see the speaker pod kit HD#76000505. It actually comes with the harness that runs between the 2 speakers and the harness that goes up to the fairing and plugs into the radio. Because I was unsure if the harness that plugs into the stereo was part of the kit(and the dealer did not know, again) I ordered one off EBay. That number is HD# 69200489(I have an extra going up for sale soon). As I stated in another post, before you put this harness under the tank, tape your power wire for the amplifier to it(trust me, you will want an amp after you hear 4 speakers and how weak they are). The picture shows the harness with the red power wire for the amp attached to it. You will connect it to the Y-harness that plugs into the 2 rear speakers. That Y-harness will go on top of the metal plate in the bottom of the tourpak, tape it down just like the light harness underneath. Also, take the plug off and run the wire thru the grommet you will put in the bottom of the tourpak.
Here is where you may get a little aggravated but you will need to drill a hole in the shifter side bottom of the tourpak for a grommet to go in. The grommet can be the same size as the one used for the lights, HD#11447. Make sure you measure the diameter of the area between the 2 flanges on the outside of the grommet to get the drill size for your hole. As far as locating the hole, I marked it just at the front edge of the metal plate on the shifter side and then pulled the plate out and took the tourpak off the rack. Put tape over the outside area you are drilling so you don't pop a bunch of paint off the outside of the tourpak. Before putting the plate back in, take a grinder and make a U-shaped area where the wiring comes up thru the grommet so it will not hit the plate(and make sure you de-burr it good). Look at pictures and see what I did, and do that. Clean all shavings out of tourpak and put grommet in and re-install bottom plate and install tourpak on mounting rack. Pull wires down thru grommet and then put plug back on the wires on the outside of the tourpak. Tape the speaker harness in the tourpak down so it will not rub around. Run plugs for speakers over and into each of the bass adapters and connect to speakers after you get tourpak mounted on bike.
Attached Images
File Type: jpg SAM_1023.jpg (86.9 KB, 182 views)
File Type: jpg SAM_1024.jpg (82.5 KB, 193 views)
nking262 is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Road Glide Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in













Similar Threads
Thread Thread Starter Forum Replies Last Post
Adding run brake and turn to your King tour pack? steventammy Lighting 8 08-20-2017 04:37 PM
Adding LED to Airwing Rack 2015 RG michigander Do-IT-Yourself 4 03-29-2016 06:29 PM
2015 Detach tourpak on a 2012 CVO RG DONVITO *General Road Glide Discussions/Pictures 13 03-17-2015 07:54 PM
Adding a TourPak, need wiring assistance. SilverGhost Aftermarket Accessories 4 11-01-2012 09:20 AM
WTT Black Pearl Tourpak for Vivid Black Tourpak letsgofast Wanted! (Buy or Trade) 1 08-03-2012 01:54 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome