Road Glide Forums - Reply to Topic
Controls & Handlebars Controls and Handlebars for Road Glides

Thread: Changed bars now alarm goes on bike wont start Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Road Glide Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
02-28-2018 06:19 AM
y2kflhr
Quote:
Originally Posted by Stray Mutt View Post
If you haven't already taken care of this, definitely pull both right side wire bundles at the same time. Good luck, if you haven't already done the new bars. Always a fun exercise.
I'm 90% done with the job, I wound up pulling the wires separately, I ran 2 pull lines, one through the end of the bars and one through the throttle wire hole....mine are jaffe bars and there was no way they were going through together. I stripped the plastic off of the throttle wires and rewrapped with shrink tubing to make the bundle tighter also. Clutch side was a breeze but did it twice because I'm a dumbass and ran the wires through the bar end not the hole for the perch....ooops! d
02-27-2018 10:33 PM
Stray Mutt
Quote:
Originally Posted by y2kflhr View Post
question for you, since I will probably be pulling wires this weekend, do you pull the tbw and control wires at the same time or one group at a time, I got my bars from freaky and they have some nasty bends in them, not sure what brand they are.
If you haven't already taken care of this, definitely pull both right side wire bundles at the same time. Good luck, if you haven't already done the new bars. Always a fun exercise.
02-23-2018 11:44 AM
y2kflhr question for you, since I will probably be pulling wires this weekend, do you pull the tbw and control wires at the same time or one group at a time, I got my bars from freaky and they have some nasty bends in them, not sure what brand they are.
02-23-2018 12:15 AM
Stray Mutt
Quote:
Originally Posted by hd4cruzin View Post
Thanks Ron, But I got this issue resolved. What bars are you going with?
Glad you got it worked out. I'm going with the 12 inch chisled's. Got 'em cheap, so it's kind of a fly n try. Honestly, the stock bars are comfortable for me. I just hate the look.
02-22-2018 07:52 PM
hd4cruzin
Quote:
Originally Posted by Stray Mutt View Post
Troy and I will be doing the bars on my CVO this weekend, Bill. I'll try to remember to note the wiring and relay the info to you.
Thanks Ron, But I got this issue resolved. What bars are you going with?
02-22-2018 04:36 PM
Stray Mutt
Quote:
Originally Posted by hd4cruzin View Post
Thanks for the help guys. Here is an update...... I had a U1040 code that I cleared and that solved the alarm issue. Bike starts now but am throwing some TGS codes. I think I crossed the TBW wires when putting the pins back in connector. The issue is I switched to the CVO TBW and there is no wiring diagram that came with the TBW and there are 2 red, 2 black and 2 white wires. 1 each color in the yellow sleeve and black sleeve for those that have switched to the CVO TBW will know what I mean. Does anyone with the CVO TBW have the way the pins go into the connector under the fairing? That is what I have to check.


Sent from my iPad using Tapatalk
Troy and I will be doing the bars on my CVO this weekend, Bill. I'll try to remember to note the wiring and relay the info to you.
02-22-2018 02:39 PM
wevsspot See if this helps;

https://www.shop.harley-davidson-ros...s/56032-08.pdf

You don't need to read the whole thing, but on page 6 it lists the molex cavity that each of the wires needs to be installed in.

And you might find this helpful as well;

https://www.roadglide.org/24-controls...tml#post201061

Space
Space
02-15-2018 02:22 PM
hd4cruzin
Changed bars now alarm goes on bike wont start

Thanks for the help guys. Here is an update...... I had a U1040 code that I cleared and that solved the alarm issue. Bike starts now but am throwing some TGS codes. I think I crossed the TBW wires when putting the pins back in connector. The issue is I switched to the CVO TBW and there is no wiring diagram that came with the TBW and there are 2 red, 2 black and 2 white wires. 1 each color in the yellow sleeve and black sleeve for those that have switched to the CVO TBW will know what I mean. Does anyone with the CVO TBW have the way the pins go into the connector under the fairing? That is what I have to check.


Sent from my iPad using Tapatalk
02-15-2018 08:26 AM
wevsspot If all of the other electrical parts and pieces work, I'll bet that you failed to properly disarm the security system prior to disconnecting the battery (which I'm assuming that you did before you started working on the bars). If that is indeed the issue, and you set your security PIN code at some point during your ownership of the bike, you can reset the system using the PIN code.

From the Harley instructions;

Using the Security Alarm PIN Override to Start Your Harley Davidson (pre 2014)

1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window

2. Enter the first digit of your PIN by pressing the LEFT turn signal switch (X) times

3. Press the RIGHT turn signal switch 1 time to move to the next digit

4. Enter the second digit of your PIN by pressing the LEFT turn signal switch (X) times

5. Press the RIGHT turn signal switch 1 time to move to the next digit

6. Enter the third digit of your PIN by pressing the LEFT turn signal switch (X) times

7. Press the RIGHT turn signal switch 1 time to move to the next digit

8. Enter the forth digit of your PIN by pressing the LEFT turn signal switch (X) times

9. Press the RIGHT turn signal switch 1 time to move to the next digit

10. Enter the fifth digit of your PIN by pressing the LEFT turn signal switch (X) times

11. Press the RIGHT turn signal switch 1 time to move to the next digit

12. Press the RIGHT turn signal switch 1 time and the security system alarm is turned off.
02-15-2018 06:44 AM
skratch silly question, but you do have the fob with you when you do this? is the battery in the fob good?
This thread has more than 10 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome